Tag: slab

Post drilled reusable anchor connector - Persoal fall protection UK

Reusable anchor connector

Post drilled reusable anchor connector - Persoal fall protection UK

Post drilled reusable anchor connector certified according to EN795, used for fall arrest and work restraint systems as personal fall protection. Zinc plated reusable connection hanger to mount with Non-reusable expansion anchor (product code SSAN008). This anchor connector is used with a non-reusable expansion anchor as part of a two-component post-drilled anchor. It is designed for solid concrete slabs to provide an anchorage point for single-user lanyards or fall arrestors, or in pairs to form anchorage at the end of running-lines (temporary horizontal lifeline) when used for work restraint.

This anchor device is designed to be used on horizontal, vertical and sloping surfaces and is suitable as a replacement for a Scissorsafe anchorage device when a cast-in void former has been omitted or cast unsuccessfully. This anchor is designed for personal fall protection and should only be used with or as part of a work restraint or fall arrest system. We strongly recommend that you load-test any friction anchor before attaching a personal safety system to it. For more advice please refer to product code SCSHYD for load-testing advice.

Product code SSAN009

Temporary edge protection with precast socket on construction site in UK

Omnia floor slabs

precast_socket_safetyrespect_5330c

Our Precast socket is designed to be casted into precast concrete slabs right at the concrete factory. This provide an easier, faster and safer mounting of temporary edge protection at the construction site.

An Omnia flooring slab is a reinforced precast concrete slab which incorporates a triangular lattice girder that is attached to a lower layer of reinforcement. The lattice girder is manufactured using high strength steel wire which binds with in-situ concrete which is poured onto it.

By casting a Precast socket (product code 911108) into the lower slab means that temporary edge protection can be installed onto the slab before it is lifted into position allowing rebar installation and concrete placing onto the slabs within a collectively protected work area.

Precast sockets are fixed to rebar before the lower portion concrete is cast. A cut length of Protective sleeve (product code 911107) is inserted onto the Precast socket, which forms a 50 mm diameter hole around the Post and allows extraction when temporary edge protection is no longer required.

The Precast socket has an integrated post lock. Post 1,3 m and Barrier 2,6 are installed either before or after the prefabricated element is lifted in place. The Barriers can easily be lifted to the desired height when casting. No tools are needed.

PRODUCTS
• Precast socket
• Protection sleeve for Precast socket
• Post 1,3 m
• Barrier 1,3, 2,6
• Frame barrier alu 1,3, 1,95, 2,6
• Frame barrier holder
• Adjustable link bar

precast_socket_safetyrespect_2082x

precast socket temporary edge protection concret constructionprecast_socket_safetyrespect_5344c

precast_socket_safetyrespect_5344

Frame barrier edge protection

 

Temporary edge protection on steel structures at construction site

Sacrificial sockets on steel sections

Temporary edge protection on steel structures at construction site

Installing temporary edge protection onto the top surface of the steel section offers protection to anyone working on a steel structure before a unitised facade system is installed onto its perimeter. The temporary edge protection sits within the building line without protrusions to affect the facade installation. Sacrificial sockets are welded to steel structures during fabrication and cast into the floor slabs. The temporary edge protection system is quick and easy to fix to the sections before they are hoisted into the structure.

PRODUCTS
• Welding socket
• Post 1,3 m
• Post 1,5 m alu
• Barrier 1,3, 1,95, 2,6

Collective edge protection on steel structures at construction site

Temporary edge protection on steel structures at construction site

Temporary edge protection on steel structures at construction site

Temporary edge protection on steel structures at construction site

Collective edge protection on steel structures at construction site

Temporary edge protection on steel structures at construction site

beams_and_columns_safetyrespect_0075

Edge protection installation on steel beams

Edge protection installation on steel structures

Welding socket for installing edge protection

 

Collective edge protection for Exclusion zone at construction site in UK

Freestanding edge protection

blocking_safetyrespect_7073c

When installing prefabricated concrete slabs a movable edge protection is required for safe blockage for other construction personnel. For this the Ground support plate is used together with Socket base, Post 1,3 m and Barrier 2,6. The Barriers then work as effective and safe blockage while the installation of prefabricated concrete slabs is carried out by workers with personal fall protection equipment.

PRODUCTS
• Ground support plate
• Socket base
• Post 1,3 m
• Barrier 1,3, 2,6
• Personal fall protection equipment

blocking_safetyrespect_5548

blocking_safetyrespect_7073

Temporary edge protection on concrete floor slabs at construction site in UK

Precast concrete floor slabs

Temporary edge protection on concrete floor slabs at construction site in UK

Pre-casting concrete elements allows for inclusion of cast-in components to support the temporary edge protection system needed to erect the structure. If edge protection is needed on top of the slab, anchor sockets can be cast to support a Post foot (product code 912105). For side of slab positioning cast-in anchors will support Vertical brackets (product code 912118).

Omnia slabs can be delivered with Precast socket (product code 911108) projecting from the top of the bottom concrete layer.

Socket with Rebar 400 mm is an expendable socket that is embedded into slabs or beams with a minimum depth of 500 mm.

If anchoring is to be avoided, Adjustable clamps 300 or 550 can be installed on site before the units are lifted into position.

In the brackets our Post 1,3 m is installed and thereafter Barrier 2,6. The Barrier can be raised in one simple operation on the post up to a height of 310 mm above the floor structure, without decreased safety. This creates conditions for joint grouting, casting and other common work tasks without any need of uninstalling the edge protection.

SafetyRespect offer technical support and will provide a schedule of the equipment required to protect your door openings.

PRODUCTS
• Post foot
• Socket base
• Precast socket
• Socket with rebar 400 mm
• Clamp 300
• Clamp 550
• Post 1,3 m
• Barrier 1,3, 2,6
• Cast protection for Post foot
• Cast protection for Socket base

Temporary edge protection on concrete floor slabs at construction site in UK

Post foot edge protection bracket for concrete_slab egde constructions UK

standard_system_safetyrespect_0136c

Adjustable Clamp 300 as attachment for collective edge protection on concrete slab floor

standard_system_safetyrespect_0114c

Temporary edge protection with precast socket on construction site in UK

VT Catch fan

Catch fans on slab edges

VT Catch fan

Catch fan for slabs is a complement to our temporary edge protection system. The fan is a collective safety measure that catch and contain falling objects where access is required in the immediate vicinity of a high rise structure. The fan can be installed without any need of cranes and this version is designed to be installed on concrete floor slabs edges.

Catch fans are designed to fit directly vertically or horizontally onto building frames or scaffolding structures using a range of accessories. They are for and six meters wide with a three meter overhang, and fixed directly to the top of the slab using reusable anchor bolts. The fans are compact, lightweight and transportable between work areas without the use of a crane.

Catch fans are installed up to six meters below the working area and they will catch and absorb the energy of falling object or debris, ensuring that they don’t bounce out of the net. They can also protect the public in, for example, city environments. A fine mesh layer is fixed to the net to catch smaller objects. Fallen objects are retrieved by simply folding the net to gain access. They can easily be moved and adapted throughout the construction project. Easy to fold to a vertical position in order not to interfere with cranes.

PRODUCTS
• Catch fan 4m
• Catch fan 6m
• Slab fix

VT Catch fan on slab at construction site

VT Catch fan on slab at construction site

VT Catch fan lifted at construction site

VT Catch fan on slab at construction site

VT Catch fan on slab at construction site

VT Catch fan on slab at construction site

VT Catch fans at construction site

VT Catch fan

VT Catch fan

Post foot

Post foot

Post foot

The Post foot (product code 912105) connects to the top of concrete slabs keeping the edge clear for fixing facade brackets, when unitised curtain-walling is to be installed or when masonry forms the external facade.

The Post foot is fixed to the concrete slab using reusable screw anchors, which carries an economical benefit if the edge protection system is to be reused around the project. It is designed to hold a standard system post (product code 912110) which are held captive in the socket base using a twist-lock design, which prevents accidental uplift or removal. The Post foot can also be used with Cast protection (product code. 911140).

• Weight 1,1 kg.
• 100 pieces delivered in stacking box stillage.

Art no. 912105

Product sheet

Post foot edge protection

Post foot edge protection bracket for concrete_slab egde constructions

Post foot edge protection bracket for concrete_slab egde constructions

Post foot edge protection bracket for concrete_slab egde constructions UK

Post foot edge protection bracket for concrete_slab egde constructions UK

Standing seam bracket

On roof base and cover with double seam the Standing seam bracket can be used as attachment for the edge protection. The bracket can be adjusted to four positions for roof inclinations from 5 to 40 degrees. The standing seam bracket is installed so that the seam lock gets a grip under the seam. The sheets must be of good quality and be fastened against the roof construction.

On roof bases the Standing seam bracket is installed above the roof frame with
wood screws.

• Installed on steel sheet, cover.
• Quick installation.
• Handles various roof angles.
• Does not damage the steel sheet.
• Hot dip galvanized.
• Weight 2,6 kg.

Art. No. 930103

Product sheet

standing_seam_bracket_safetyrespect_2

standing_seam_bracket_safetyrespect_4

standing_seam_bracket_safetyrespect_5

standing_seam_bracket_safetyrespect_033c

Balcony bracket

Balcony bracket 10 gr

Balcony bracket

Inclined bracket for edge protection that facilitates installation of external panel wall. The ordinary attachment for the balcony railing can be used for installing the Balcony bracket. After that Post 1,3 m together with Barrier 2,6, Barrier 1,3 or Barrier 1,95 are installed in order to adapt the edge protection according to the dimensions of the balcony.

• Fits all common balcony attachments.
• M10 or M12.
• Hot dip galvanized.
• Weight 1,3 kg.

Art. No. 912160

Product sheet

Edge protection balcony